It contains important safety information. Con- sult a Yamaha dealer if the fuel system needs to be drained instead. Stay alert for holes, rocks, or roots in the terrain, and oth- er hidden hazards which may cause the ma- chine to upset. . Remove the quick fasteners and pull the panel upward. You may use distilled water if you gine and radiator are still hot. Then pull forcefully, Starting the engine without setting the being careful not to pull the rope all the way drive select lever to the park position out.
A headlight bulb is hot when it is on and To raise the beam, turn the adjusting screw in immediately after it is turned off. Lubricate the inner cables and the cable ends. The tires listed below have been ap- The following are minimums: proved by Yamaha Motor Co. Engine oil dipstick preload adjusting ring 16. Remove the battery and charge it. Before riding, check that the brake fluid is above the lower level and replenish when necessary. Drive select lever box check hose 1.
A precise blend of top-quality, mineral-base oil and ultra-clean additives provide superior antifrictional properties. It provides stable clutch performance and the strength needed to protect the engine from the wear and tear of daily use. If there is room to do so by steering in the direc- unexpected and uncorrected, sliding could tion of the slide. You may lose control of the machine or overturn. Use the electric starter to see if there is compression. The oil filter is on the oil pump at the rear of the crankcase.
Be sure to keep your feet Could cause loss of control or a colli- firmly mounted on the footboards at all times. If the cables do not operate smoothly, ask a Yamaha dealer to replace them. Ask a Yamaha dealer to No compression. Refer to page 6-4 for the drive select lever operation. Fuel expands when it heats up. These procedures should be performed by a Yamaha dealer. Remove the coolant reservoir cap, and 1.
Note: a special technique is required when braking as you go down a hill. Never climb hills with excessively slippery or loose surfaces. See page 4-20 for seat removal and installation procedures. When the machine is not used for a month or longer, remove the battery and store it in a cool, dark place. Dealer quantities and individuals price s shown. A precise blend of top-quality, mineral-base oil and ultra-clean additives provide superior antifrictional properties.
This adjust- ment however, should be left to a professional Specified idle speed: Yamaha service technician. Removing the radiator cap when the en- The radiator fan operation is completely gine and radiator are still hot. If necessary, apply 14 inches in depth. Pause a few seconds before the next attempt. Cheers - Jeff Answer: Given the make and year, I would go with a 10W40 viscosity. Rear shock absorber spring 15. Be sure to read each section on the room.
You should also wear eye protection goggles or face shield , gloves, boots, long-sleeved shirt or jacket, and long pants. Other tire combina- Rear 27 kPa 0. These procedures should be performed by a Yamaha dealer. Otherwise, the rubber seals may dete- riorate, causing leakage and poor brake performance. Disconnect the hose on the coolant res- water.
It provides stable clutch performance and the strength needed to protect the engine from the wear and tear of daily use. Dismount on uphill side or to a side if pointed straight uphill. With the rear brake applied, shift the Parking on a hill or other incline. Do not attempt to diagnose such problems yourself. This information will be needed to order spare parts from your Yamaha dealer. Special wrench the left and right side to the same set- ting. This lets the gas flow through on to the piston which then seeps by the rings into the crank case.
With the purchase of this Yamaha, you can now appreciate the high degree of crafts- manship and reliability that have made Yamaha a leader in these fields. Wheel nut torque: Front: 55 Nm 5. The speed limiter keeps the throttle from fully opening, even Do not operate at speeds too fast for your when the throttle lever is pushed to the maxi- skills or the conditions. See page 6-1 for details. Inflate the tires very slowly and carefully.
To install Place the panel in the original position and in- stall the bolts. Because the engine is during this period, consult a Yamaha dealer. A separate starter circuit supplies this mixture. Standard position: B A- Minimum soft E- Maximum hard 4-22. Remove the coolant reservoir cap. Never open the throttle suddenly. Remove the tailpipe by pulling it out of the muffler.