Please call Dahmer Powertrain toll free number for availability: 1-877-595-9065. As you remove the starter motor, disconnect the wiring for the starter by removing its nuts. The new belt will need more clearance to get on the pulley. Separate the engine from the transaxle and remove it out the top keyboard knackerd now Thanks for the writers, mintalkin. The power steering pump on the Ford focus is located on the firewall at the rear of the engine compartment on the upper driver's side.
Drain the coolant Screw the drain plug back in after draining. I also had the front and rear of the car weighed separately. Remove the intermediate shaft bracket. Only cut wires that you are sure you will not use later. Before starting this process I took the car to a local scrap metal yard and had the car weighed.
Boost the energy of your older vehicle with a replacement 2007 Ford Focus engine or use high-quality parts to revive your existing engine. Disconnect the crankcase breather hose. A Focus with a Duratec engine can be the most difficult because you need to remove the intake manifold. Call Surefire at 1-800-790-9094 for customer service, availability and technical assistance. Cut those worries out of your mind by selecting from AutoZone's top-quality line of Focus replacement engines. This took a while to figure out but eventually we just pulled the ends loose and they popped off the linkages.
This must be done correctly. If the starter has to be removed for replacement, you first need to know the type of engine your model Focus has. I'm not a mechanic so I was fortunate to have someone more familiar with the process to assist. Once the 10 Ford Focus serpentine belt replacement is around the tension pulley, release the socket wrench and allow the tension pulley to take up the slack on the Automotive Serpentine Belt Replacement. Remove the bolt and tube.
For Application Questions Please Call Surefire at 800-790-9094. Not sure how true that is but tearing into the engine will let me know. Do not remove the bolts. This provides a lot of access for getting under the car to remove things, and for dropping the engine out. Back in the garage I backed the car up onto ramps, jacked up the front of the car, and placed 3 very solid jackstands under the front frame and suspension. After several slides on the hammer we got it to pop loose.
Disconnect the windshield washer hose and clips. . Once the 10 Ford Focus serpentine belt replacement is around the pulleys, allow the 2010 Ford Focus serpentine belt replacement to hang freely at the bottom of the engine. Remove the torque converter cover bolts. Turn the wrench handle, the pulley moves and the tension on the belt slackens. For most Focus models, apply the parking brake and raise the car's front end on axle stands. Detach the coolant hose from the water pump.
This requires you to remove the oil level dipstick tube, the air intake pipe from the throttle body, the electrical connectors from the throttle position sensor and idle air control valve, and the vacuum hoses and wiring harness from the manifold. An 2010 Ford Focus serpentine belt replacement too small will bind the pulleys while an 10 Ford Focus serpentine belt replacement too large will just fall off. This process took a couple of days over a weekend, with an assistant or two helping for most of that time. Once all the needed parts are disconnected, disconnect all the mounting bolts from the starter motor, then release it from the dowels on the transmission housing to remove it from the engine. Remove the power steering pump and position it to one side. Take your pick from our unbeatable in-store assortment and benefit from free battery charging and engine diagnostic testing while you shop. Take the belt off the pulley and let it hang.
Cover the end with a plastic bag held by rubber bands twisted around the hose, since it will leak. Remove the engine front mounting. Remove the drive belt cover. Remove the four retainers two each side and remove the hood. Raise the engine slightly to prevent pressure on the support insulators. Knock Sensor Mount on Right Side. Failure to do so may result in personal injury.
Call Surefire at 1-800-790-9094 for customer service, availability and technical assistance. Worse case, yank the engine and replace. Power steering pump pressure switch. You should remove certain parts to reach the starter motor, and the exact parts vary depending on the type of engine the car has. I was told that the engine needed to be replaced as the belt damaged the engine.