It is a 2 piece plastic cover. All this crap about things being snap in, and pull out by hand and slide back in is just lies. When moving the lever to release the locking collar make sure you push gently on the square piece of plastic next to the lever. If you touch the bulb with your fingers clean the oils off with rubbing alcohol. If changing the driver's side bulb, remove the battery cover, and the battery before you start. The drivers side headlamp went out so I tried to change it. Push the electrical connector on to the base of a new high beam bulb.
Replacing headlights for Volkswagen Jetta is one of the easiest repairs to make. Examine first where the holes are inside the frame where the clips grab the head lamp assembly. Recently replaced the passenger side headlight bulb on a 2000 Passat. To access the bulb socket you need to depress the tab near the cover while lightly prying the cover from behind. If not e-mail me and I can scan and e-mail you thdiagrams I got from the library.
Changing both headlight bulbs on your Jetta at the same time will allow both bulbs to have the same intensity and prevent the new headlight bulb from appearing brighter than the bulb on the opposite side. Also pull the liver up and out toward the light. Be careful as the tab can snap because it is made of plastic, but I pressed it pretty hard and it did not. . You may have to use a flashlight when replacing the headlight cover plate so you can see the two slots that the right end has to go into. Look under the car, towards the rear passenger door, along the side of the undercarriage. I took me some time to get this done because it was the first time for me and I wasnt sure this was right or not.
Hope this helps you do it in an hour or less. You have to take the air deflector off. The six plastic fasteners mine had eight look just like nipples, please excuse my french. I also responded to this same web page and answer the question by explaining the way from underneath the fender well and reaching up to the lamp for removal. Not sure if that is true on all Golfs.
If your Jetta has this type of bulb, we do not recommend that you attempt to change it yourself. However this slide mechanism is very tough to move the first time. Some earlier units also had a locking clip. T-10 torx driver at least 3 inches long. Thank you so much for this info, it worked like a charm. You just open that and replace the element inside and the two o-ring gaskets ones big and ones small.
Replacement bulbs with their part numbers are as follows: Low Beam , High Beam , Turn Signal A. Today is March 26, 2011, I just changed the right headlight on our 2001 New Beetle. For more, check out my other. Feel free to use any Volkswagen Jetta light bulb sizing that is listed on Sealight but keep in mind that all information here is provided as is without any warranty of any kind. This needs to be depressed to release the slide mechanism which releases the headlight.
If you are replacing it install a new bulb. One is located before the catalytic converter, and one after the catalytic converter. In some Volkswagens, the highbeam is the same bulb as the headlight and it is possible for the highbeam to work, but the headlight be burnt out even if they are the same bulb and vise versa. This won't work and causes great frustration. The casing will hang over your bumper Pull out the headlight and plug the new one in. Push the new bulb into the socket, put the socket back into the housing, and twist a quarter turn clockwise to secure the socket into the fixture slide unit back into place, line up screw holes and replace screws tightly. I'm not a big fix-it girl, but my uncle told me it's relatively straightforward so I gave it a try… The easiest way is to access the bulb assembly is from the bottom of the car, there is a plastic cover under the fender and in front of the tire that can be removed by unscrewing two screws and two nuts.
These covers a plastic, and in coldweather, or in a vehicle that hasn't been recently worked on, theycould snap. Unplug the wiring harness attached to the headlight bulb. Last night I had to drive home with just my high beams on because both headlights were out. Do one side first, so you can use the other side as a reference. If you found this guide to be helpful, please consider making a small donation by clicking on the PayPal. Replacing them is just the opposite. Now, pull out the plug with wires, then undo the s … pring clip, then remove old bulb.
Same for replacemen … t. Pull the rubber dust cap off the rear of the high beam bulb and set it aside in a safe place. Push the new bulb into the socket, put the socket back into the housing, and twist a quarter turn clockwise to secure the socket into the fixture My wife has a 2001 Pontiac Grand Am. Firstly, remove the clean air intake Big black plastic tube behind the headlamp. In some Volkswagens, the highbeam is the same bulb as the headlight and it is possible for the highbeam to work, but the headlight be burnt out even if they are the same bulb and vise versa.