To help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. Engine exhaust may enter the vehicle. Be sure the battery has enough water. Remove the two screws holding each of the license plate lamps. There are two identical bolts on the side of the Tranny case, both are sunk into small pits, one lower and one upper, drop the lower one out to drain the fluid and the other one to fill it up after you put the bottom one back in first The in-flow and drain for the transmission fluid are two 8mm hex keys, however I had to take a grinder to mine to shorten it so it would fit in between the hole and the frame. Perform a rear tire change by removing the rear tire and installing the compact spare tire in the rear wheel location. It can cause unconsciousness and even death.
You must use the rear tire to replace the front flat tire. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire and Loading Information label. To the right of it is an 11 mm plug to remove. I could have been injured and I fear driving the car thinking something else will break down. Remove the kit from the foam container. A transmission fluid leak is the only reason for fluid loss. Be sure to use the following steps to do it safely.
When adding, be sure to fill to the approximate level, as recommended in this manual. See When to Add Engine Oil under E. Lift the trunk liner to access the spare tire and tools. An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. The metric unit for air pressure. There is a cap to fill the transmission directly on top of the transmission. The car was bought brand new in 2007 and had regular maintenance done on the car, ie brakes, oil, filters.
You… There is no dip stick on a 2008 Chevy Cobalt. One has to completely drain the transmission to know how much transmission fluid is in there and then you have to put the exact amount in that the manual calls for. Oils meeting this standard may be identified as synthetic. All kinds of noise, all pot holes I thought the car was going to fall apart. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing. Wash the windshield thoroughly when cleaning the blades. Remove the stow bolt extension rod and sleeve from the jack.
In a crash, they might not be able to provide adequate protection. Turn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line. Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. In an emergency, use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later, if needed, to get all the rust or dirt off. Press the tabs to release the bulb assembly. The adjustment screw can be turned with a 6 mm socket wrench.
The location on the 2. People have been hurt doing this, and some have been blinded. Tighten each nut by hand until the wheel is held against the hub. Electric Engine Cooling Fan B. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability. Remove the two bolts from the headlamp assembly. If transmission has been overfilled, allow fluid to drain out.
If the vehicle only has a cigarette lighter, use the cigarette lighter. The driver side rear turn signal comes on to indicate that corner sensor is ready to be learned. Turn off the engine when refueling. The air cleaner not only cleans the air; it helps to stop flames if the engine backfires. Static electricity discharge from the container can ignite the fuel vapor. . Jack and Wheel Wrench F.
Everyone I ever spoke to never heard of a clutch burning out so soon. With the engine running, shift transmission through all gears. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Brought back to the dealer several times for sagging doors on two door model, irregular idol, rattling sounds in the front end to no avail. Inflate the tire to the recommended inflation pressure using the pressure gage E. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Remove the retainer A that holds down the jack, wheel wrench B and spare tire C.
They can damage your vehicle because there is not enough clearance. This coolant is designed to remain in the vehicle for five years or 150,000 miles 240 000 km , whichever occurs first. Bolt To store a flat tire and tools: 1. Use the wheel wrench to loosen all the rear wheel nuts. You may decide not to lift the hood when this warning appears, but instead get service help right away. Clean safety belts only with mild soap and lukewarm water.
Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Unscrew the oil filler cap the cap where you put the oil into the engine. The compressor will inflate the tire with air only. See Rear Tire Changing Procedure in this section. Posted on Jun 20, 2009 if it is a automatic transmission just open the hood and there is a tube other than the oil tube usually the opposing side of the engine between the engine and the fire wall it has a long dip stick just like the oil stick and this fluid level should be checked when engine is running in park,If it is manual transmission it is usually a sealed unit. If your vehicle has a compact spare tire, see number of plies in the sidewall and under the tread.